How Much Is a New Radiator in the UK? [2026 Prices]

Written by Russell Brooks · Founder

Last updated: November 2026

Quick Answer

Supply and fit a standard single panel radiator costs £200–£400 in the UK in 2026. A double panel convector costs £250–£500, and a designer or column radiator £400–£1,200. Labour for a like-for-like swap is £80–£150 (1–2 hours). Adding a new radiator to an existing system costs £200–£400 including pipe extension. The key trade is a plumber or heating engineer.

Plumber fitting a new radiator in a UK home

What Does a New Radiator Cost in the UK?

Replacing a radiator is one of the more routine heating jobs a plumber or heating engineer carries out. Whether you have a radiator with a persistent cold spot, visible corrosion, or a weeping leak that cannot be fixed at the valve, knowing what a replacement costs before you call someone out avoids surprises.

In 2026, the total cost to supply and fit a standard single panel radiator in the UK is £200–£400. A double panel convector — the most common type in UK homes — runs £250–£500 fitted. Designer and column radiators carry a wider range: £400–£1,200 fitted, depending heavily on the unit itself. If you are buying the radiator separately and just paying a plumber to swap it, expect to pay £80–£150 in labour for a straightforward like-for-like replacement.

Adding a completely new radiator to a room that does not currently have one — which involves running new pipework from an existing circuit — costs more: typically £200–£400 for the work alone, before the radiator itself. The total project cost depends on how far the pipes need to run and whether floors or walls need to be lifted to route them.

Radiator Replacement Cost by Type

The biggest variable in the total project cost is the radiator itself. Standard panel radiators are inexpensive to buy; designer and column radiators cost significantly more. The labour element is relatively constant for a like-for-like swap regardless of the unit, since the pipework and valve connections are the same size.

Radiator TypeSupply Only (DIY)Supply & Fit
Single panel (Type 10/11)£40–£120£200–£400
Double panel convector (Type 22)£60–£200£250–£500
Double panel single convector (Type 21)£55–£180£240–£480
Designer / flat panel£100–£500£300–£800
Column radiator (cast iron style)£150–£800£400–£1,200
Labour only (like-for-like swap)—£80–£150
Adding new radiator to existing system—£200–£400 (labour only)
TRV supply & fit (per valve)—£30–£60

Supply and fit prices include a standard TRV and lockshield valve set. Column and designer radiators may require non-standard valve fittings at additional cost. Source: Sleepless Tradesman UK Trades Rate Index 2026. Source: Sleepless Tradesman UK Trades Rate Index 2026.

What Affects the Cost of Replacing a Radiator?

Like-for-like vs new installation

Replacing an existing radiator with a new one of the same size using the existing valve connections and brackets is the simplest and cheapest job. The plumber drains the radiator, unhangs it, fits the new one to the existing brackets and pipe tails, and refills. This takes 1–2 hours. Adding a radiator to a room that has never had one is a different scope entirely: new pipework must be run from an existing circuit, potentially under floors or through walls, before the radiator itself can be hung. This can take half a day or more.

Radiator size and BTU output

Radiators are sized by their BTU (British Thermal Unit) output, which must match the heat loss of the room they serve. A larger radiator costs more to buy. If you are upgrading to a bigger radiator to improve heating in a cold room, the new unit may not align with the existing brackets or pipe centres, adding a small amount of extra work to reposition brackets and extend the pipe tails. Use a BTU calculator to confirm the right size before ordering.

Valve condition

TRVs (thermostatic radiator valves) and lockshield valves that have seized or are corroded need replacing at the same time as the radiator. TRVs cost £30–£60 each to supply and fit. If both valves need replacing, that adds £60–£120 to the job. On older systems, it is often worth replacing valves at the same time regardless — a seized valve that cannot isolate the radiator makes future maintenance much harder.

System condition and water quality

Heavily sludged or corroded central heating systems can cause new radiators to degrade prematurely. If the existing system water is visibly black or the engineer finds heavy magnetite sludge during the job, a powerflush (£300–£600 for the whole system) should be considered before or alongside any new radiators. Fitting a new radiator into a dirty system without flushing first risks blocking the new unit within a year or two. A magnetic system filter (around £80–£150 fitted) can be added at the same time to protect the system going forward.

Location and engineer rates

Plumber and heating engineer rates are higher in London and the South East. A job priced at £250 in Manchester may cost £350–£400 in London on labour alone. See the regional table below for average supply and fit costs by region.

Timing: alongside a boiler service or replacement

The best time to replace a radiator is when you are having a boiler service or a new boiler installed. The engineer is already on site, the system will be drained down or under reduced pressure as part of the boiler work, and you avoid a separate call-out charge. If you have multiple radiators to replace, doing them all in a single visit saves significant cost compared to individual call-outs.

Tradesperson van parked on a UK residential street ready for a job
Local tradesperson rates vary significantly across UK regions

Regional Radiator Replacement Costs Across the UK

The table below shows average supply and fit costs for a standard double panel convector radiator by region in 2026.

RegionAverage Supply & Fit Cost
London£280–£600
South East£240–£520
South West£210–£460
Midlands£200–£420
North West£200–£430
North East£190–£400
Yorkshire£195–£410
Wales£195–£420
Scotland£200–£430
Northern Ireland£185–£400

Figures are for a standard double panel convector radiator (600×1000mm approx.) supplied and fitted by an independent plumber or heating engineer, including TRV and lockshield valve. Designer and column radiators cost more.

When Should You Replace a Radiator?

Not every radiator problem requires a full replacement. Understanding which issues can be resolved cheaply and which warrant a new unit saves unnecessary expense.

Cold spots: bleed first, then assess

A cold spot at the top of a radiator is almost always trapped air. Bleeding the radiator — a DIY task that takes under five minutes with a radiator key — releases the air and restores full heat output. This costs nothing and should always be the first step. Cold spots at the bottom of the radiator, or cold spots that keep returning after bleeding, suggest sludge build-up. A powerflush may fix this without needing to replace the radiator at all.

Leaks: valve vs radiator body

Most radiator leaks originate at the valve connections, not the radiator body. A weeping TRV or lockshield joint can often be re-tightened or resealed without replacing the radiator. A leak from the radiator body itself — a pinhole in the steel — cannot be repaired cost-effectively and means the unit needs replacing. Rust weeping through a painted surface is a warning sign that the steel is corroding from inside.

Age: 15–20+ years

Steel panel radiators typically last 15–20 years before internal corrosion becomes a significant problem. A radiator of this age that is showing cold spots, discolouration, or any external rust is a candidate for replacement. At that age, the internal steel will have thinned in places even if the outside looks acceptable. Replacing older radiators at the same time as a new boiler installation is common practice and cost-effective.

Upgrading output for a cold room

If a room is consistently cold despite the system working correctly, the existing radiator may simply be undersized for the room. This is common in extensions or rooms where the original radiator was sized decades ago before insulation was improved (or not improved) elsewhere. Use a BTU calculator to work out the heat loss for the room and compare it to the output of the existing radiator. If the radiator is significantly undersized, upgrading to a larger unit will make a material difference to comfort.

Bleeding vs Replacing a Radiator

Bleeding a radiator is a free, 5-minute DIY job that any homeowner can do. You need a radiator bleed key (£1–£2 from any hardware shop), a cloth to catch drips, and a few minutes. Turn the bleed valve anti-clockwise a quarter turn, let the air hiss out, and close the valve as soon as water starts to appear. Then check and re-pressurise the boiler if the pressure dropped below 1 bar.

Bleeding is the right answer for trapped air. It is not the answer for cold spots caused by sludge, internal corrosion, an undersized radiator, or a faulty TRV that is not opening correctly. If bleeding does not resolve a cold spot, or if the same radiator needs bleeding repeatedly every few weeks, the underlying cause needs investigating before spending on a replacement.

A plumber called out to diagnose a cold spot will typically charge their standard call-out rate (usually £60–£100 depending on region) plus an hourly rate of £50–£90 for any subsequent work. Knowing whether the problem is air, sludge, or a faulty radiator before calling someone out can save a wasted diagnostic visit.

Radiator Sizing: BTU Calculations

Radiators are rated in BTU (British Thermal Units per hour). The BTU output needed for a room depends on the room's volume, the insulation standard, the number and type of windows, the external walls, and the room's intended temperature. A correctly sized radiator will heat the room to the target temperature on the coldest days without the boiler struggling.

As a rough guide for a well-insulated modern home:

  • Small bedroom (10 m²): 2,000–3,500 BTU
  • Medium bedroom (12 m²): 3,000–4,500 BTU
  • Living room (20 m²): 5,000–8,000 BTU
  • Open-plan kitchen/diner (30 m²): 7,000–12,000 BTU
  • Large room with poor insulation: add 20–30% to the above figures

Use an online BTU calculator to get a more precise figure before ordering a replacement radiator. Undersizing a radiator is a common and entirely avoidable mistake that leads to a cold room and a confused homeowner — and costs another call-out to fix.

TRVs and Thermostatic Valves: What They Cost

A thermostatic radiator valve (TRV) lets you control the temperature of individual rooms by regulating the flow of hot water into each radiator. TRVs are standard on most modern UK central heating systems and are required under Part L of the Building Regulations for replacement radiators in most circumstances.

Supplying and fitting a new TRV alongside a radiator replacement typically costs £30–£60 per valve. If your existing TRV is functioning correctly and is compatible with the new radiator, the plumber may reuse it. TRVs on older radiators often have a 15mm or 10mm connection: confirm the valve size matches the pipework before ordering a replacement radiator with valve tails already fitted.

Smart TRVs (compatible with systems such as Hive, Nest, or Honeywell) cost more to supply — typically £40–£100 per valve — but allow remote temperature control per room from a phone app. These are worth considering if you are replacing multiple radiators in a home with a compatible smart heating system.

Powerflush: When Cleaning Is Better Than Replacing

Before replacing a radiator with cold spots caused by sludge, it is worth considering a powerflush of the whole system. A powerflush uses high-pressure water and chemical descalers to clear magnetite sludge, limescale, and corrosion deposits from every radiator and pipe in the system. The cost of a powerflush in the UK is typically £300–£600 for a whole-house system (8–10 radiators).

A powerflush also includes a chemical flush of each individual radiator, which eliminates cold spots from sludge without the cost of replacement. If multiple radiators in the same house have cold spots, a powerflush is almost always the more cost-effective fix compared to replacing several units.

However, if a radiator is leaking from the body, visibly corroded, or more than 15–20 years old, a powerflush will not extend its useful life significantly. In these cases, replacement is the right answer, ideally combined with a system flush to protect the new unit.

Frequently Asked Questions

Can I replace a radiator myself?

A like-for-like radiator swap is technically DIY-able: drain the system, disconnect the old radiator, fit the new one, and refill. However, working on a central heating system incorrectly can cause leaks, air locks, or system pressure problems. If you need to extend pipework, adjust valves, or add a new radiator to the system, that work is best left to a qualified plumber or heating engineer. If your boiler is gas, any work on the gas connections must be done by a Gas Safe registered engineer.

How long does it take to replace a radiator?

A straight like-for-like radiator replacement takes 1–2 hours for a plumber. This includes draining down the section of pipework, removing the old radiator, fitting the new one, refilling and bleeding, and testing for leaks. Adding a new radiator to an existing system with pipe extension work takes 3–5 hours depending on the complexity of the pipework run.

Do I need to drain the system to replace a radiator?

No, not always. A plumber can isolate a single radiator using its lockshield and TRV valves and drain just that radiator without draining the whole system. This only works if the valves are operational and not seized. On older systems where the valves have not been turned for years, the valves may need replacing too, which does require draining the system or at least that section of pipework.

How do I know when a radiator needs replacing?

Key signs that a radiator needs replacing include: persistent cold spots that do not resolve after bleeding, visible corrosion or rust on the panels or at the valve connections, a weeping or active leak from the body of the radiator (not from a valve joint), significant external damage or denting, and age over 15–20 years. Cold spots at the bottom of a radiator often indicate sludge build-up: a powerflush may resolve this without needing replacement.

Can I replace one radiator without draining the whole system?

Yes. A plumber can close the lockshield valve and TRV on the radiator being replaced, drain just that radiator into a bucket, fit the new radiator, and refill it. The rest of the system stays filled and pressurised throughout. This is the standard approach for a like-for-like swap and is why a single radiator replacement takes only 1–2 hours. If the valves are seized, the engineer may need to drain a section of the system to replace them safely.

Find a Plumber or Heating Engineer Near You

Compare quotes from local plumbers for radiator replacement and central heating work.

Get radiator replacement quotes

Related Guides

Written by Russell Brooks · Founder

Last updated: November 2026